|
|
ISO Fixtures |
|
|
|
||
ISO34-1
DIN
ISO34-1
|
Rubber, vulcanized
or thermoplastic — Determination of tear strength — Part 1: Trouser, angle
and crescent test pieces |
|
ISO37
|
Rubber, vulcanized or thermoplastic — Determination
of tensile stress-strain properties |
|
ISO178
DIN EN ISO178
|
Plastics — Determination of flexural properties |
TH22-5P-CWR2+5x110-CX15-OX30 |
ISO527-2
DIN EN ISO527-2
|
Plastics --
Determination of tensile properties -- Part 2: Test conditions for moulding
and extrusion plastics |
|
ISO527-3
DIN EN ISO527-3
|
Plastics —
Determination of tensile properties — Part 3: Test conditions for films and
sheets |
|
ISO604
|
Plastics -
Determination of compressive properties |
|
ISO813
DIN ISO813
|
Determination of adhesion
to a rigid substrate - 90 degree peel method |
|
ISO898-1
DIN EN
ISO898-1
|
Mechanical
properties of fasteners made of carbon steel and alloy steel -- Part 1:
Bolts, screws and studs with specified property classes -- Coarse thread and
fine pitch thread |
|
ISO1288
DIN EN
ISO1288
|
Glass in building —
Determination of the bending strength of glass — Part 3: Test with specimen
supported at two points (four point bending) |
|
ISO1806
DIN EN
ISO1806
|
Fishing nets -
Determination of mesh breaking force of netting |
|
ISO1922
|
Shear properties of
sandwich core materials |
|
ISO1926
|
Rigid cellular
plastics — Determination of tensile properties |
|
ISO2137
|
Petroleum products
and lubricants - Determination of cone penetration of lubricating
greases and petrolatum |
|
ISO2759
DIN EN
ISO2759
|
Board -
Determination of bursting strength |
|
ISO3037
DIN EN ISO
3037
|
Corrugated fibreboard
— Determination of edgewise crush resistance (unwaxed edge method) |
|
ISO3303-1
DIN EN
ISO3303-1
|
Bursting strength
of rubber- or plastics-coated fabrics - Part 1: Steel-ball method |
|
ISO3327
DIN EN ISO3327
|
Hardmetals -
Determination of transverse rupture strength |
|
|
ISO3347 |
Wood —
Determination of ultimate shearing stress parallel to grain |
|
ISO3377- 2
|
Leather -
Physical and mechanical tests - Determination of tear load -
Part 2: Double edge tear |
|
ISO3379
|
Leather -
Determination of distension and strength of surface (Ball burst method) |
|
ISO3386-1
DIN EN
ISO3386-1
|
Polymeric
materials, cellular flexible - Determination of stress-strain
characteristics in compression - Part 1: Low-density materials |
|
ISO3781
DIN ISO3781
|
Paper and board --
Determination of tensile strength after immersion in water |
|
ISO4013
|
Concrete —
Determination of flexural strength of test specimens |
|
ISO4578
|
Adhesives -
Determination of peel resistance of high-strength adhesive bonds -
Floating-roller method |
|
ISO4624
DIN EN
ISO4624
|
Paints and
varnishes, pull off test for adhesion |
|
ISO4919
|
Textile floor
coverings - Determination of tuft withdrawal force |
|
ISO5173
DIN EN
ISO5173
|
Destructive tests
on welds in metallic materials - |
THS1018 |
ISO6237
|
Adhesives – wood-to-wood
adhesive bonds. Determination of shear strength by tension loading. |
|
ISO6238
|
Testing of small
clear specimens of timber |
|
ISO6259-3
|
Thermoplastics
pipes – Determination of tensile properties – Part 3: Polyolefin pipes |
|
ISO6312
|
Road vehicles -
Brake linings - Shear test procedure for disc brake pad and drum brake shoe
assemblies |
|
ISO6507-2
DIN EN
ISO6507-2
|
Metallic
materials - Vickers hardness test - Part 2: Verification and
calibration of testing machines |
|
ISO6872
DIN EN ISO6872
|
Dentistry -
Ceramic materials |
|
ISO6892
DIN EN ISO 6892
|
Metallic
materials - Tensile testing - Part 1: Method of test at room
temperature |
THS265-CSS12.7x63
(Type 2) |
ISO7198
|
Cardiovascular
implants and extracorporeal systems — Vascular prostheses — Tubular vascular
grafts and vascular patches. |
|
ISO7206
|
Implants for surgery
— Partial and total hip joint prostheses — Part 4: Determination of endurance
properties and performance of stemmed femoral components. Gliding nail
fatigue test. |
|
|
ISO7389 |
Building construction - Jointing products -
Determination of elastic recovery of sealants |
|
|
ISO7438 DIN EN ISO7438 |
Metallic materials — Bend test |
|
ISO/IEC7810
|
Identification cards - Physical characteristics |
|
|
ISO7808 |
Plastics - Thermosetting
moulding materials - Determination of transfer flow |
|
ISO7864DIN EN ISO7864
|
Tensile test fixture to test sterile hypodermic needles |
|
|
ISO7886-1 |
Sterile hypodermic
syringes for single use - Part 1: Syringes for manual use |
|
|
ISO7961 |
Aerospace — Bolts —
Test methods |
|
ISO8295
DIN EN
ISO8295
|
Plastics -
Film and sheeting - Determination of the coefficients of friction |
|
ISO8339
DIN EN
ISO8339
|
Determination of
tensile properties of sealants used in joints in building construction
conform |
|
ISO8490
|
Metallic materials
- Sheet and strip - Modified Erichsen cupping test |
|
ISO8493
DIN EN
ISO8493
|
Metallic
materials - Tube - Drift-expanding test |
|
ISO8510-1
|
Adhesives — Peel
test for a flexible-bonded-to-rigid test specimen assembly — Part 1: 90
degree peel |
|
ISO8515
|
Textile-glass-reinforced
plastics - Determination of compressive properties in the direction parallel
to the plane of lamination |
|
ISO8627
|
Dentistry; Stiffness
of the tufted area of tooth-brushes |
|
|
ISO9046 |
Building
construction - Jointing products - Determination of adhesion/cohesion
properties of sealants at constant temperature |
|
ISO9073-5
|
Textiles -
Test methods for nonwovens - Part 5: Determination of resistance to
mechanical penetration (ball burst procedure) |
|
ISO9073-7
DIN EN
ISO9073-7
|
Textiles - Test
methods for nonwovens - Part 7: Determination of bending length |
|
ISO9187-1
|
Injection equipment for medical use - Part
1: Ampoules for injectables |
|
ISO9073-18
DIN EN
ISO9073-18
|
Textiles — Test methods for nonwovens — Part 18:
Determination of breaking strength and elongation of nonwoven materials using
the grab tensile test |
|
|
ISO9626 DIN
EN ISO9626 |
Stainless steel needle tubing for the manufacture of
medical devices - Requirements and test methods |
|
|
ISO9836-1 DIN
EN ISO9836-1 |
Geosynthetics - Determination of thickness at
specified pressures - Part 1: Single layers |
|
ISO9895
|
Paper and board - Compressive strength -
Short-span test |
THS733-310 |
ISO10319
DIN EN
ISO10319
|
Geosynthetics - Wide-width tensile test |
|
ISO/IEC10373-1
|
Identification cards
- Test methods - Part 1: General characteristics |
|
ISO10545
DIN EN
ISO10545
|
Ceramic
tiles - Part 2: Determination of dimensions and surface quality |
|
ISO/TS11405
|
Dentistry
— Testing of adhesion to tooth structure |
|
|
ISO11542-2 |
Plastics -
Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion
materials - Part 2: Preparation of test specimens and determination
of properties |
THS941 |
|
ISO11644 |
Leather
- Test for adhesion of finish |
THS1186-20
|
|
ISO11979-3 |
Ophthalmic
implants - Intraocular lenses - Part 3: Mechanical properties
and test methods. Compression test. |
THS1486 |
|
ISO12192 |
Paper
and board — Determination of compressive strength — Ring crush method |
|
ISO12236
DIN EN
ISO12236
|
Static
puncture test on geotextiles |
|
ISO12625-5
DIN EN
ISO12625-5
|
Tissue paper and
tissue products - Part 5: Determination of wet tensile strength |
|
|
ISO12625-9 |
Tissue paper and
tissue products - Part 9: Determination of ball burst strength |
|
ISO13503-2
DIN EN
ISO13503-2
|
Petroleum and
natural gas industries -- Completion fluids and materials - Part 2:
Measurement of properties of proppants used in hydraulic fracturing and
gravel-packing operations |
|
ISO13779-4
|
Implants for
surgery - Hydroxyapatite - Part 4: Determination of coating adhesion strength |
|
|
ISO13934 |
Textiles -
Tensile properties of fabrics - Part 1: Determination of maximum
force and elongation at maximum force using the strip method |
|
|
ISO13936-3 |
Textiles -
Determination of the slippage resistance of yarns at a seam in woven
fabrics - Part 3: Needle clamp method |
THS1108 |
ISO13953
|
Polyethylene (PE) pipes
and fittings – Determination of the tensile strength and failure mode of test
pieces from a butt-fused joint |
|
ISO13954
|
Plastics pipes and
fittings - Peel decohesion test for polyethylene (PE) electrofusion
assemblies of nominal outside diameter greater than or equal to 90 mm |
|
|
ISO14125 |
Fibre-reinforced plastic
composites - Determination of flexural properties |
TH22-5P-CWR2+5x110-CX15-OX30 TH238-St-ISO178 |
ISO14126
|
Fibre-reinforced
plastic composites - Determination of compressive properties in the
in-plane direction |
|
|
ISO14130 |
Fibre reinforced
plastic composites - Determination of apparent interlaminar shear
strength by short beam-method |
|
ISO14272
|
Resistance welding
- Destructive testing of welds - Specimen dimensions and procedure for cross tension
testing of resistance spot and embossed projection welds |
|
|
ISO14555 |
Welding - Arc
stud welding of metallic materials |
THS1556 |
|
ISO14704 |
Fine ceramics (advanced ceramics, advanced technical ceramics) —
Test method for flexural strength of monolithic ceramics at room temperature |
|
ISO14801
DIN EN
ISO14801
|
Dentistry -
Implants - Dynamic loading test for endosseous dental implants |
|
ISO14916
|
Thermal spraying - Determination
of tensile adhesive strength |
|
ISO15361
|
Pulps -
Determination of zero-span tensile strength, wet or dry |
|
ISO15630-2
|
Steel for the
reinforcement and prestressing of concrete - Test methods -
Part 2: Welded fabric and lattice girder |
|
ISO16770
|
Plastics - Determination
of environmental stress cracking (ESC) of polyethylene - Full-notch
creep test (FNCT) |
THS1270 |
ISO17697
|
Footwear - Test
methods for uppers, lining and insocks - Seam strength |
|
|
ISO19095-3 |
Plastics -
Evaluation of the adhesion interface performance in plastic-metal
assemblies - Part 3: Test methods |
|
ISO19671
|
Additional lubricants for male natural rubber latex condoms — Effect
on condom strength |
|
ISO20482
DIN EN
ISO20482
|
Testing of metals; Erichsen
cupping test on sheet and strip metal having a width of >= 90 mm;
Thickness range: 0.2 mm to 2 mm |
|
ISO20795-1
DIN EN ISO20795-1
|
Dentistry - Artificial teeth for
dental prostheses |
|
ISO20932-2
|
Textiles - Determination of the elasticity of fabrics -
Part 2: Multiaxial tests |
|
ISO21182
|
Light conveyor belts - Determination of the coefficient of
friction |
|
ISO21809-3
|
Petroleum and natural gas industries — External coatings for buried or
submerged pipelines used in pipeline transportation systems — Part 3: Field
joint coatings. Annex H (peel strength test). |
|
|
ISO22112 |
Dentistry - Artificial teeth for dental prostheses |
|
ISO22254
|
Dentistry -
Manual toothbrushes - Resistance of tufted portion to deflection |
|
|
ISO23910 |
Leather - Physical
and mechanical tests - Measurement of stitch tear resistance |
|
|
ISO23936-2-B.2 DIN
EN ISO23936-2-B.2 |
Petroleum, petrochemical and
natural gas industries - Non-metallic materials in contact with media
related to oil and gas production - Part 2: Elastomers |
|
ZT 16 May
2020
|
|
|
